WT2
Arrayable two-way compact theatre enclosure
features
Q
Q
Q
Q
Q
Q
Arrayable compact trapezoid enclosure
High SPL output capability
70º coverage angle
Multi-laminate birch plywood construction
Switchable active/passive operation
Certified MAN quick-connect flying option
applications
Q
Q
Q
Theatre sound systems
Club sound reinforcement
Music playback in nightclubs
The WT2 is a powerful, compact theatre system which can be used as a stand-alone enclosure in a distributed
system or arrayed in multiples. The switchable active/passive two-way cabinet is very efficient, combining
smooth dynamic full-frequency performance with excellent articulation, utilising high power drive units for
maximum SPL.
Optimum performance is achieved with the MX5 or DX1 controller configured for the WT2 to perform
system specific equalisation, phase adjustment, crossover and limiter functions. With a Wavefront Series sub-
bass system, ultra-low frequency enhancement takes the power bandwidth to below 35Hz.
Century Point, Halifax Road, Cressex Business Park,
High Wycombe, Buckinghamshire HP12 3SL, England.
Telephone: +44 (0)1494 535312 Facsimile: +44 (0)1494 438669
E-mail: [email protected]
All information is Copyright © 2006 Martin Audio Ltd.
1 of 5
WT2
Arrayable two-way compact theatre enclosure
frequency responses
Century Point, Halifax Road, Cressex Business Park,
High Wycombe, Buckinghamshire HP12 3SL, England.
Telephone: +44 (0)1494 535312 Facsimile: +44 (0)1494 438669
E-mail: [email protected]
All information is Copyright © 2006 Martin Audio Ltd.
3 of 5
WT2
Arrayable two-way compact theatre enclosure
overall dimensions
Century Point, Halifax Road, Cressex Business Park,
High Wycombe, Buckinghamshire HP12 3SL, England.
Telephone: +44 (0)1494 535312 Facsimile: +44 (0)1494 438669
E-mail: [email protected]
All information is Copyright © 2006 Martin Audio Ltd.
4 of 5
WT2
Arrayable two-way compact theatre enclosure
technical specifications
architectural and engineering specifications
TYPE
Compact two-way trapezoid, switchable
active/passive
The loudspeaker system shall be of the two-way
switchable active/passive type consisting of one 12"
(300mm) direct radiating reflex loaded low frequency
transducer and one 1" (25mm) exit HF compression
driver mounted on a constant directivity horn in a
trapezoidal plywood enclosure. The enclosure shall be
fitted with an integral pole mounting socket and
threaded inserts to facilitate a variety of mounting
options. Active or passive operation shall be selected by
a switch at the rear of the enclosure. In active mode the
loudspeaker shall be bi-amped and operated with a
separate electronic controller. In passive mode, low and
high frequency sections shall be integrated by an
internal 2kHz passive crossover network.
FREQUENCY RESPONSE (5) 70Hz-18kHz 3dB
-10dB @ 52Hz
DRIVERS
12" (300mm) / 3" (75mm) voice coil
1" (25mm) exit HF compression driver
LF/(LF + HF): 400W AES, 1600W peak
HF: 60W AES, 240W peak
RATED POWER (2)
RECOMMENDED AMPLIFIER 400-600W into 4 ohms
SENSITIVITY (6)
LF/(LF + HF): 98dB
HF: 107dB
MAXIMUM SPL (7)
NOMINAL IMPEDANCE
123dB continuous, 129dB peak
LF/(LF + HF) 8 ohms
HF: 8 ohms
70º horizontal, 40º vertical
2kHz active/passive
Textured black paint
Black perforated steel
2 x Neutrik NL4
10 x M8 threaded inserts
1 x mounting pole socket
2 x MAN blanking plates
2 x rear kelp fittings
DISPERSION (-6dB)
CROSSOVER
FINISH
PROTECTIVE GRILLE
CONNECTORS
FITTINGS
Performance of the loudspeaker system with its
electronic controller shall meet or exceed the following
criteria:
2 x front lid fittings
DIMENSIONS
WEIGHT
(W) 365mm x (H) 554mm x (D) 364mm
(W) 14.4ins x (H) 21.8ins x (D) 14.3ins
24.5kg (54lbs)
Frequency response measured 1 metre on axis shall be
70Hz-18kHz 3dB.
High frequency dispersion at -6dB points shall be
70˚H x 40˚V.
Power handling shall be 400W AES, 1600W peak
LF/(LF+HF), 60W AES, 240W peak HF.
Rated impedance shall be 8 ohms LF/(LF+HF).
Maximum SPL measured at 1 metre on axis shall be
122dB continuous, 128dB peak.
accessories
WT2LID
HTKWT2Y
HTKCT05
GPT060
Lid
Flying yoke
8mm Shouldered eye bolt
Fitted enclosure flying points
Lightweight install stud
HTKLIS
Dimensions (W) 365mm x (H) 554mm x (D) 364mm
(14.4ins x 21.8ins x 14.3ins).
Weight 24.5kg (54lbs).
N o t e s
The loudspeaker system shall be the Martin Audio
WT2.
(1) Measured on-axis in half space at 2 metres, then referred to 1 metre.
(2) AES Standard ANSI S4.26-1984.
(3) Measured in half space at 2 metres with 1 watt input, using band limited pink noise, then referred to 1 metre.
(4) Measured in half space at 2 metres using band limited pink noise, then referred to 1 metre.
(5) Measured on-axis in open (4π) space at 2 metres, then referred to 1 metre.
(6) Measured in open (4π) space at 2 metres with 1 watt input, using band limited pink noise, then referred to 1 metre.
(7) Measured in open (4π) space at 2 metres using band limited pink noise, then referred to 1 metre.
Tr a d e D e s c r i p t i o n s A c t
Due to Martin Audio’s policy of continuing improvement, we reserve the right to alter these specifications without prior notice.
Martin Audio is committed to refining state of the art sound reinforcement, combining in-depth product and field applications
research with advanced manufacturing techniques. Every Martin Audio product is built to the highest manufacturing standards
and rigorously tested to ensure that it meets the performance criteria specified in the design.
Century Point, Halifax Road, Cressex Business Park,
High Wycombe, Buckinghamshire HP12 3SL, England.
Telephone: +44 (0)1494 535312 Facsimile: +44 (0)1494 438669
E-mail: [email protected]
All information is Copyright © 2006 Martin Audio Ltd.
5 of 5
|