ATT-1855CIB-d05.qxp 4/8/2005 5:35 PM Page 1
User Manual (Part 2)
Speakerphone/
Answering System 1855
with Caller ID & CallWaiting
/
ATT-1855CIB-d05.qxp 4/8/2005 5:36 PM Page 1
User Manual (Part 2)
Speakerphone/
Answering System
1855
/
Table of contents
Getting Started
Answering System Operation
Answering system operation ..........17
Day and time announcements........18
Outgoing announcements................19
Announce Only mode......................20
Changing feature options.................21
Message playback...............................22
Recording and playing memos........23
Message window displays.................24
Remote access....................................25
Quick reference guide ........................2
Parts checklist.......................................3
Before you begin..................................4
Telephone installation .........................5
Wall mounting ......................................6
Telephone Operation
Basic operation.....................................8
Options while on calls........................9
Feature menu......................................10
Appendix
Memory Dialing
Icons, tones & indicator lights.........26
In case of difficulty.............................27
INDEX..................................................29
One touch dialing..............................12
Speed dialing .......................................12
Entering numbers...............................13
Caller ID Log
How Caller ID works.......................14
To review your call log.....................15
To dial a call log entry......................16
1
ATT-1855CIB-d05.qxp 4/8/2005 5:36 PM Page 2
Getting Started
Quick reference guide
/
Answering
Memory
dialing
system
controls
Telephone
function keys
Telephone
function keys
Telephone function keys (see pages 8-9)
REDIAL ..................Press to redial last number called.
FLASH ....................During a call, press to receive an incoming call, if you
subscribe to a Call Waiting service.
VOLUME ................Press to adjust volume of ringer or active call.
MUTE ......................Press to silence microphone; press again to resume.
SPEAKER ..............Press to turn speakerphone on or off (begin or end a call).
Answering system controls (see pages 17-24)
Repeat message, record
memo or change menu
settings.
Skip to next message,
record announcement or
change menu settings.
Press to play or stop playing messages.
Press and hold to play old messages.
REMOVE ................Press to delete message currently playing.
ON/OFF ..................Press to turn answering system on or off.
SETUP ....................Press to review, press and hold to change answering
system options.
CLOCK....................Press to review, press and hold to set the day and time.
Memory dialing (see pages 12-13)
DISPLAY DIAL........Press and then lift handset (or press SPEAKER) to dial
number displayed on screen.
PROG/MEM ............Press to program or dial a number in Speed Dial memory.
M1-M3 ....................Press to dial a One Touch Dialing number.
(See pg 13 in User Manual for memory programming
instructions).
2
ATT-1855CIB-d05.qxp 4/8/2005 5:36 PM Page 3
Getting Started
Parts checklist
Remember to save your sales receipt and original packaging in case you ever need to
ship your telephone for warranty service. Check to make sure the telephone package
includes the following:
/
Power
adapter
Handset cord
Telephone
Telephone
handset
Telephone line cord
Directory card
Wallet card
Quick Start Guide
3
ATT-1855CIB-d05.qxp 4/8/2005 5:36 PM Page 4
Getting Started
Before you begin
About Caller Identification
Caller ID with Call Waiting features in
this telephone let you see who’s calling
before you answer the phone, even
when you’re on another call.These
features require services provided by
your local telephone company.
Contact your telephone service
provider if:
• You have both Caller ID and Call
Waiting, but as separate services
(you may need combined service)
• You have only Caller ID service, or
only Call Waiting service
• You don’t subscribe to any Caller
ID or Call Waiting services.
You can use this phone with regular
Caller ID service, and you can use its
other features without subscribing to
either Caller ID or combined Caller
ID with Call Waiting service.There
may be fees for these services, and
they may not be available in all areas.
Caller ID features will work only if
both you and the caller are in areas
offering Caller ID service, and if both
telephone companies use compatible
equipment.
See Caller ID Operation, beginning on
page 14, for more details about how
these features work.
4
ATT-1855CIB-d05.qxp 4/8/2005 5:36 PM Page 5
Getting Started
Telephone installation
Install the telephone as shown below. Choose a location where the phone is not
exposed to excessive heat, cold, dust or moisture.
Plug line cord into
telephone jack.
Plug power cord
transformer into
electrical outlet.
Route cord through slot.
AC 6V
TEL LINE
POWER
Plug coiled handset
cord into jack on left
side of telephone.
NOTE: Use only the power cord supplied with this product. If you need a replacement, call 1 800 222–3111.
Be sure to use an electrical outlet not controlled by a wall switch.
5
ATT-1855CIB-d05.qxp 4/8/2005 5:37 PM Page 6
Getting Started
Wall mounting
The telephone can be installed on any standard wall-phone outlet. Choose a location
where the phone is not exposed to excessive heat, cold, dust or moisture.
AC 6V
TEL LINE
POWER
Press and pull to remove wall-mount bracket.
Turn bracket upside down.
Insert bracket tabs into lower notches.
Press down firmly to click in place.
6
ATT-1855CIB-d05.qxp 4/8/2005 5:37 PM Page 7
Getting Started
Wall mounting
Plug line cord into telephone, then wrap
cord around posts as shown below. Leave a
few inches free, enough to route wire under
tabs and plug into the wall jack.
Line cord
Power cord
After cords are connected, press and
slide down firmly so phone is held
securely on outlet mounting pegs.
Plug power cord transformer
into electrical outlet.
/
Remove handset cradle tab, rotate and replace to
hold handset securely in place when wall mounted.
7
ATT-1855CIB-d05.qxp 4/8/2005 5:37 PM Page 8
Telephone Operation
Basic operation
Making and answering calls
To answer a call, lift the handset, or press SPEAKER to
use the speakerphone.
To make a call, lift the handset (or press SPEAKER),
then dial a number. Replace the handset (or press
SPEAKER) to hang up.
Hands-free speakerphone calls
To answer an incoming call, press SPEAKER. To make a
call, press SPEAKER, then dial a number. When the
handset is out of the cradle you can press SPEAKER to
toggle between hands-free speakerphone and normal
handset use. Press SPEAKER again to hang up.
MSG#
Last number redial
555 1234
0
REDIAL
The most recently dialed number is displayed when you
lift the handset or press SPEAKER. Press REDIAL to dial
it again.
To adjust ringer volume
Volume level
To adjust the ringing volume, press the VOLUME but-
tons while the phone is idle. Each button press raises
or lowers the ringer volume by one level. You can turn
the ringer off, or select one of seven volume levels.
MSG#
4
4 NEW
22 CALL
8
ATT-1855CIB-d05.qxp 4/8/2005 5:37 PM Page 9
Telephone Operation
Volume level
MSG#
Options while on calls
4
To adjust listening volume
Press the VOLUME buttons to adjust listening volume.
There are eight volume levels for the speakerphone,
and four levels for the handset. Each button press
raises or lowers listening volume by one level.
Call waiting
If you have Call Waiting service, you will hear a beep if
someone calls while you are already on a call. Press
FLASH to put your current call on hold and take the
new call. You can press FLASH at any time to switch
back and forth between calls.
Light is on when phone is muted
Mute
Press MUTE to silence the microphone during a call.
You will be able to hear, but your caller will not be able
to hear you until you press MUTE again to resume your
conversation.
9
ATT-1855CIB-d05.qxp 4/8/2005 5:37 PM Page 10
Telephone Operation
Turn off answering system
(red light off)
Feature menu
In the feature menu you can customize how the tele-
phone works. Make sure the answering system is off
(red light off), then press SET UP repeatedly until the
feature you want is displayed. Press SKIP/REPEAT to
change settings. Press SET UP again to accept the new
setting and move to the next feature.
Press SET UP to select feature.
Press SKIP/REPEAT to change.
Press SET UP to save.
Contrast
MSG#
Press SKIP/REPEAT to adjust screen contrast to maxi-
mize readability in different lighting conditions.There
are five contrast levels (1-5).
4
0
SET CONTRAST
Call history
MSG#
Press SKIP/REPEAT to turn the Caller ID log on or off:
• All Calls: Each incoming call is logged.
• No Calls: No Caller ID information is kept.
0
CALL HISTORY
Repeated calls
MSG#
The Caller ID log notifies you when multiple calls are
received from the same number. Press SKIP/REPEAT to
turn this feature on or off:
0
REPEATED CALLS
• Combined: Only the most recent call from each
number is kept.A “REP” icon is displayed if more
than one call is received from the same number.
• Separate: Each call is logged, even if the same person
calls more than once.
Call waiting
MSG#
When on, the telephone displays and logs Caller ID
information if you get a new incoming call while on an
existing call. Press SKIP/REPEAT to turn this feature on
or off.
0
cid-CALL WAIT
10
ATT-1855CIB-d05.qxp 4/8/2005 5:37 PM Page 11
Telephone Operation
Feature menu
Language
MSG#
Press SKIP/REPEAT to select the language used in all
menus and screen displays.You can choose English,
Espanol or Francais.
0
WHICH LANGUAGE?
Home area code/Local area codes
MSG#
Caller ID numbers are not always displayed in the
correct dialing format.To make callbacks easier, you can
enter your home area code so that it is not included
when a number is displayed or dialed.
HAC--
0
HOME AREA CODE?
MSG#
You can also enter up to 4 local area codes for areas
nearby. When you receive a call from one of these
areas, the local area code is automatically included
when the number is displayed or dialed.
LAC1--
0
LOCaL AREA CODE
Use the keypad to enter your home area code, then
press SET UP to enter up to 4 other area codes if
desired.
When you dial a Caller ID entry:
• Calls from your designated home area code will be
dialed out using 7 digits, without the area code
(i.e., 555-1234)
• Calls from your designated local area codes will be
dialed out using 10 digits, with the area code included
(i.e., 818-555-1234).
11
ATT-1855CIB-d05.qxp 4/8/2005 5:37 PM Page 12
Memory dialing
MSG#
555 1234
3
Memory capacity
The telephone can store up to 12 numbers in memory
locations for quick dialing. Each memory location can
store a number up to 24 digits long.
One touch dialing (M1-M3)
To dial numbers stored in One Touch buttons, lift the
handset (or press SPEAKER), then press a One Touch
button (M1, M2, M3).
Speed dialing (1-9)
MSG#
To dial numbers in Speed Dialing memory locations:
1 Lift the handset (or press SPEAKER).
2 Press PROG/MEM.
555 1234
3
3 Press a digit to dial the location you want (1-9).
Directory card
The directory card provided with your telephone can
be used to record names or numbers stored in memory
locations.The back peels off to expose an adhesive
surface so you can attach it to the underside of the
handset if desired.
Directory card
M1- Mom
M2- Bill at work
M3- School
1- John Smith
2- Betty Johnson
3- Pat Taylor
4- Chris Williams
If you pause for too long while programming
a memory location, the procedure will time out and you
will have to begin again.
NOTE:
NOTE: If you store a number in a memory location
that is already in use, the old number will be
overwritten with the new number.
12
ATT-1855CIB-d05.qxp 4/8/2005 5:38 PM Page 13
Memory Dialing
Press PROG/MEM, then enter number
MSG#
Entering numbers
555 1234
0
One touch dialing (M1-M3)
To program One Touch buttons:
1 Press PROG/MEM.
ENTER NUMBER
2 Enter a telephone number (up to 24 digits), or
import one by pressing REDIAL or REPEAT/MEMO.
Press PROG/MEM, then press button
(M1-M3) or enter location (1-9)
3 Press PROG/MEM.
MSG#
4 Press a One Touch button (M1, M2, M3).
0
5 Repeat steps 2-4 to program another button, or
ENTER LOCATION?
press REMOVE to save and exit.
Speed dialing (1-9)
To program Speed Dialing memory locations:
1 Press PROG/MEM.
2 Enter a telephone number (up to 24 digits), or
import one by pressing REDIAL or REPEAT/MEMO.
MSG#
3 Press PROG/MEM.
0
STORED
4 Press a digit to select the location you want (1-9).
Repeat to enter another number, or
press REMOVE to exit.
5 Repeat steps 2-4 to program another memory
location, or press REMOVE to save and exit.
Options while entering numbers
• Press SKIP to erase numbers if you make a mistake.
• Press REPEAT twice to enter a 3-second dialing pause.
• Press REMOVE to exit without saving the number.
To change numbers
To change a number, follow the steps above to enter
another number in its place.
13
ATT-1855CIB-d05.qxp 4/8/2005 5:38 PM Page 14
Caller ID Log
MSG#
12:34 10-23
PM
How Caller ID works
555 234
0
If you subscribe to Caller ID service provided by your
local phone company, information about each caller will
be displayed after the first or second ring.
Pat Williams
/
Information about the last 50 incoming calls is stored in
your call log. You can review the call log to find out
who has called, or return the call without dialing.
If you answer a call before the information appears on
the screen, it will not be saved in your call log.
Light on: New call(s) received
MSG#
/
0
4 NEW
22 CALLs
Total calls
New (unviewed) calls
New call (unviewed)
Time/date of call
Repeat call
(see page 10)
NEW
REP
MSG#
12:34PM10-23
1
No:
Call number
(1 to 50)
555 1234
0
Caller’s number
Pat Williams
Caller’s name
14
ATT-1855CIB-d05.qxp 4/8/2005 5:38 PM Page 15
Caller ID Log
No:
1
MSG#
12:34 10-23
PM
To review your call log
555 1234
Pat Williams
0
To review your Caller ID log
Press REPEAT/MEMO to display the most recent call.
Press SKIP/ANNC repeatedly to scroll through the list
of earlier calls, or press REPEAT/MEMO to scroll back
to more recent calls.
No:
2
MSG#
12:08 10-23
PM
555 4321
cHRIS THOMPSON
0
To return a call
To dial a number that is currently displayed, press
DISPLAY DIAL and then lift the handset (or press
SPEAKER) (See page 16 for important dialing options.)
If you forget to lift the handset or press SPEAKER the
display will remind you to do so by displaying "LIFT
RECEIVER".
No:
2
MSG#
12:08 10-23
PM
555 4321
cHRIS THOMPSON
0
To copy an entry into memory
To copy any displayed number (see page 16 for
important dialing options) into memory, press PROG
/ MEM. The name and time will be removed,and
the telephone number will remain in the display.
Press PROG/ MEM again.
“ENTER LOCATION?”
will appear in the display. Enter a memory location
number (1-9).
To delete entries
PressREMOVE to delete the displayed entry from your
Caller ID log. Press and hold REMOVE to delete all
entries, then press REMOVE again to confirm.
15
ATT-1855CIB-d05.qxp 4/8/2005 5:38 PM Page 16
Caller ID Log
MSG#
12:34 10-23
PM
To dial a call log entry
555 1234
3
Pat Williams
To call a number that is currently displayed, press DISPLAY
DIAL, then lift the handset (or press SPEAKER).
Dialing options
Caller ID numbers may appear with an area code that
may not be required for local calls. If the number
displayed is not in the correct format, you can change
how it is dialed.
Note: You can
also remove the area
code or add a preceding
"1" before programming
a number into memory
by pressing SETUP
once, and ANNC
repeatedly, until you
see the correct option.
While the number is displayed, press SET UP, then
press ANNC repeatedly to see various dialing options
(with or without area code, with or without preceding
“1”).
When the option you want is displayed, press DISPLAY DIAL
and then lift the handset (or press SPEAKER).
16
ATT-1855CIB-d05.qxp 4/8/2005 5:38 PM Page 17
Answering System Operation
Answering System
Operation
MSG#
4
Message capacity
Message counter
The answering system can record up to 99
Number of messages recorded (or,
during playback, message number
currently playing).
messages, depending on how long each message is.
Individual messages can be up to 3 minutes long, but
total maximum recording time is 19 minutes. Messages
will remain available for replay until you delete them.
Press to repeat message;
hold while listening to slow
down playback (see page 22).
Press to skip message;
hold while listening to speed up
playback (see page 22).
Press to start or stop message
Press and hold to record memo
(see page 23).
Press and hold record outgoing
playback (see page 22).
announcement (see page 19).
/
Press to turn answering
system on or off.
Press to delete message
(see page 22).
Press to hear feature options.
Hold to change options (see
page 21).
Press to hear day/time.
Hold to set day/time
(see page 18).
NOTE: The answering system must be on to review or change settings.
17
ATT-1855CIB-d05.qxp 4/8/2005 5:38 PM Page 18
Answering System Operation
Day and time announcements
To set day and time
Before playing each message, the answering system
announces the day and time the message was received.
Before using the answering system, you should follow
the steps at left to set the day and time, so messages
are dated correctly.
CLOCK
1
2
“Sunday”
To begin, press and hold the CLOCK button for 2 seconds.
SKIP/REPEAT
The system uses voice prompts to guide you.
“Monday”
Press until correct day is spoken.
CLOCK
Each time you press SKIP, the day, hour, minute or year
advances by one. Each time you press REPEAT, the day,
hour, minute or year is reduced by one.When you hear
the correct setting, press CLOCK to move to the next
setting.
3
4
“12 PM”
SKIP/REPEAT
“1 PM”
To check day and time
Press until correct hour is spoken.
CLOCK
You can press CLOCK at any time to hear the
current day and time without changing it.
5
6
“0”
SKIP/REPEAT
“1”
Press until correct minute is spoken.
CLOCK
7
8
“2004”
SKIP/REPEAT
“2005”
Press until correct year is spoken.
CLOCK
9
“Monday, 1 pm, 2005”
NOTE: The answering system must be on to review or change settings.
18
ATT-1855CIB-d05.qxp 4/8/2005 5:39 PM Page 19
Answering System Operation
MSG#
Outgoing announcements
A
The outgoing announcement is what callers hear when
calls are answered by the answering system.
/
The phone is pre-programmed to answer calls with
“Hello. Please leave a message after the tone.”You
can use this announcement, or replace it with a record-
ing of your own voice.
Press and hold SKIP/ANNC.
Begin speaking when “A”
appears in message window.
To record your outgoing announcement
Release button to stop recording.
Press and hold SKIP/ANNC. Begin speaking when “A”
appears in the message window.To stop recording,
release the button.The message just recorded will be
played back.
Speak into microphone.
Speak facing the telephone from about 9 inches away.
You can record an announcement up to 3 minutes long.
Announcements less than 3 seconds long will not be
recorded.
To review your outgoing announcement
Microphone
Press PROG/MEM, then SKIP/ANNC to hear the
currently used outgoing announcement.
To delete your outgoing announcement
Press PROG/MEM, then SKIP/ANNC to hear the
currently used outgoing announcement. Press REMOVE
during playback to delete your announcement.
When your announcement is deleted, calls will be
answered with the pre-programmed announcement
described above.
19
ATT-1855CIB-d05.qxp 4/8/2005 5:39 PM Page 20
Answering System Operation
MSG#
Announce Only mode
Ao
In Announce Only mode, callers hear an announcement
but cannot leave messages.This option is useful, for
example, to notify callers that you will be away for an
extended period and request that they call back after a
certain date.
“AO” (Announce Only) stops
flashing after an announcement
is recorded.
SET UP
To turn Announce Only on or off
1
for 1 second
to enter feature menu.
Press and hold
Press and hold SET UP until you hear
announcement is A” Then press SKIP/REPEAT until you
“Selected
“Selected
announcement is A”
hear the option you want:
• A: Callers hear current outgoing announcement and
can leave messages.
SKIP/REPEAT
2
3
• Announce Only: Callers hear current outgoing
announcement and cannot leave messages.
“Announce Only”
Press PLAY/STOP to save your selection and exit, or press
SET UP again to change other features (see page 21).
PLAY/STOP
To record your outgoing announcement
After turning on the Announce Only feature, follow the
procedure on page 19 to record your announcement.
If you do not record an announcement, incoming calls
Or
will be answered after 10 rings, but callers will hear
“No
and will not be able to leave a message.
Announcement”
20
ATT-1855CIB-d05.qxp 4/8/2005 5:39 PM Page 21
Answering System Operation
/
Changing feature options
When the answering system is on, you can customize
how the system operates. Press and hold SET UP to
begin, then press repeatedly to hear each feature. Press
SKIP/REPEAT to change the setting of any feature.
SET UP
1
2
3
Feature options
(Default settings underlined)
Press and hold for 1 second
to enter feature menu.
System announces:
Feature description:
SET UP
“Selected announcement is...”
Options: A / Announce Only
A: Callers can leave messages.
Announce Only: Callers cannot leave
messages (see page 19).
Press until desired feature
is heard (see list at right).
“Number of rings is...”
Options: 2-7 / 24 / 46 (default 4)
Choose number of rings before the system
answers a call (2 to 7). There are two toll-
saver options: 2/4 (2 rings if new messages,
4 otherwise) and 4/6 (4 rings if new
messages, 6 otherwise).
SKIP/REPEAT
Press until desired selec-
tion is heard.
“Message alert is...”
Options: On / Off
When on, the telephone beeps every 15
seconds when you have new messages.
SET UP
4
Press to set selection and
move to next menu option.
“Remote access code is...”
Options: 500-999 / (default 500)
Follow prompts to enter a 3-digit number
(must be between 500 and 999).
“Priority call code is...”
Options: 500-999 / (default 999)
A special tone alerts you when callers
enter this code (must be 500-999).
Or
“Announcement monitor is...”
Options: On / Off
When on, you will hear your outgoing
announcement as callers hear it.
PLAY/STOP
Press to set selection and
exit menu.
“Number announce is...”
Options: On / Off
When on, you will hear Caller ID number
spoken when a call is received.
“Store number is...”
Options: On / Off
When on, you will hear caller’s phone
number spoken before message playback.
What is Priority Call Code?
If a caller enters your Priority Call
Code while your announcement is
playing, you’ll be alerted with a
special tone so you can answer
the call.
“Accept blocked calls is...”
When on, the telephone will accept calls
from callers with blocked Caller ID.
Options: On Off
/
“Call screening is...”
Options: On / Off
When on, you can hear callers as they
leave messages.
The code is pre-set to 999. See
steps at right to change it.
“Selected ring is...”
Options: Ring style 1-4
Press SKIP/REPEAT to hear and select
one of four different ringing styles.
21
ATT-1855CIB-d05.qxp 4/8/2005 5:39 PM Page 22
Answering System Operation
Number of messages
(or, during playback, message
number currently playing).
Message playback
Press PLAY/STOP to hear only new (unheard) messages.
MSG#
Press and hold PLAY/STOP to hear all messages.
3
If you have new messages waiting, you will hear only the
new messages (oldest first).
/
Announcements
• Before each message, you will hear the day and time
it was received.
Press PLAY/STOP to begin or
end message playback.
• After the last message, you will hear “End of messages.”
If the system has less than 5 minutes of recording
time left, you will hear time remaining.
PLAY/STOP
1
Message playback begins. See
options at right.
Options during playback
PLAY/STOP
• Press VOLUME button to adjust speaker volume.
2
• Press SKIP to skip to next message (or hold down
Message playback ends.
to speed up message playback).
• Press REPEAT to repeat message currently playing.
Press twice to hear previous message. (Hold down
to slow down message playback).
NOTE: If “F” is flashing in
the message window, memory is
full. You will have to delete some
messages before new ones can
be received.
• Press REMOVE to delete message being played back.
• Press PLAY/STOP to stop playback.
To delete all messages
NOTE: If you have new
(unheard) messages, the “Delete
All” feature will not work.
To delete all messages, press and hold REMOVE while
the phone is idle (not during a call, or during message
playback).
22
ATT-1855CIB-d05.qxp 4/8/2005 5:39 PM Page 23
Answering System Operation
MSG#
Recording and playing memos
12
Memos are messages you record yourself.They are
saved, played back and deleted exactly like incoming
messages.You can record a memo as a reminder to
yourself, or leave a message for someone else if others
in your household use the answering system.
/
Press and hold REPEAT/MEMO,
then begin speaking. Elapsed
time is shown in message window.
To record a memo
Follow the steps at left to record a memo. Elapsed time
(in seconds) is shown in the message window as you
record.You can record a memo up to 3 minutes long.
Press PLAY/STOP to stop
recording.
Speak into microphone.
To play back a memo
Press PLAY/STOP to hear messages and memos (see
page 22 for other options).
Microphone
23
ATT-1855CIB-d05.qxp 4/8/2005 5:39 PM Page 24
Answering System Operation
Message window displays
0
The message window usually displays the total number
of memos and incoming messages. See the list below for
explanations of other displays in this window.
Message window
Message window displays
0
No messages waiting.
1-99
Number of messages/memos, or message
currently playing (see page 22).
Current Remote Access Code while setting
(see page 21).
0-7 / 1-8
Current ringer volume/listening volume level
while adjusting.
0-59
(counting)
Elapsed time while recording a memo (see page
23) or announcement (see page 19).
F
(flashing)
Memory is full. Messages must be deleted before
new messages can be received.
CL
(flashing)
Clock needs to be set (see page 18).
AO
Announce Only mode is on. If flashing, no
announcement has been recorded (see page 19).
--
System is answering a call, or being accessed
remotely.
--
(flashing)
System is being programmed or initialized.
-||-
(on)
--
Displayed for 1 second when any answering
system setting is turned on or off.
(off)
FS
Displayed during feature setting review.
24
ATT-1855CIB-d05.qxp 4/8/2005 5:39 PM Page 25
Answering System Operation
A 3-digit security code is
required to access your
answering system from any
touch-tone phone.This
code is “500” by default;
see page 21 to change it.
Remote access
Remote access
Press 1 to hear all messages.
Play messages
1/2
Press 2 to hear only new messages.
Press to repeat current message. Press
twice (4 4) to hear previous message.
4
Repeat or go back
4
Dial your telephone number from
any touch-tone phone.
1
Press to skip to next message.
Skip message
6
When system answers, enter your
3-digit Remote Access Code (500
unless you have changed it).
2
Press to stop any operation
Stop
5
(stop playback, stop recording).
Enter remote commands
(see list at right).
3
Press 3 to delete message during playback.
Delete message
3
Press 33 to delete all messages.
Hang up to end call and save all
undeleted messages.
4
Press to review current outgoing
announcement.
Review announcement
7
Press * 7, wait for beep, then begin speak-
ing. Press 5 to stop recording and hear
playback of new announcement.
Record announcement
*7to begin recording
5to stop recording
Press #, wait for beep, then begin
Record memo
#to begin recording
5to stop recording
The system uses voice prompts
to help you set the day, hour and
minute, and year.
speaking. Press 5 to stop recording.
1
Press *
8.
If off, system will answer after 10 rings. Enter
Turn system on
0
Turn system off
*0
You will hear the current day,
and, "to change, press
6 or 4."
your access code, then press 0 to turn on.
2
3
Press
4
repeatedly to advance
repeatedly to reduce
or press
6
Press 8 to hear current day & time. Press * 8
Review/set day & time
/
8 *8
the value of the setting.
to change day & time.
When you hear the correct value
for the day, (or hour, or minute,
Follow the steps at left to set the day and time.
or year,) press
8
to move to the
Press to hear current status of all answering
system settings.
Review settings
9
next time setting.
4
Repeat steps 2 and 3 to change
each time setting. When finished,
the system will announce the new
Press to hang up answering system.
Exit
*9
day, hour, minute, and year.
25
ATT-1855CIB-d05.qxp 4/8/2005 5:39 PM Page 26
Appendix
Icons, tones & indicator lights
Status icons
ERR
NEW
REP
No:
MSG#
1
Ringer is off (see page 8).
CL
NEW
REP
No.
New call received (see page 14).
Repeat call from same number (see page 14).
Call number (see page 14).
ERR
MSG#
CL
Error (current operation has been unsuccessful; try again).
Message number (see page 17).
If flashing, set answering system clock (see page 18).
Alert tones
“Beep”
(1 quick beep)
Confirmation tone (procedure completed).
/
“Beep-Beep-Beep-Beep-Beep”
(5 quick beeps)
Error tone (current operation has been
unsuccessful; try again).
“Beep-Beep-Beep”
(3 quick beeps, repeated)
Priority call alert (caller has entered
priority call code; see page 21).
Indicator lights
NEW CALL
On when new call(s) received since
Caller ID log last reviewed.
/
ANSWERING SYSTEM
On: Answering system is on.
Off: Answering system is off.
Flashing: New message(s) received
MUTE
On when microphone is muted.
SPEAKER
On when speakerphone is in use.
26
ATT-1855CIB-d05.qxp 4/8/2005 5:39 PM Page 27
Appendix
In case of difficulty
If you have difficulty with your phone, please try the suggestions below. For Customer
•
•
Make sure the AC adapter is plugged into an outlet not controlled by
a wall switch.
Telephone does
not work at all
Make sure the line cord is plugged firmly into the telephone and the
modular jack (see page 5).
•
•
Make sure the ringer is on (see page 8).
Telephone does
not ring
Make sure the telephone line cord and AC adapter are plugged in
properly (see page 5).
•
You might have too many extension phones on your telephone line to
allow all of them to ring. Try unplugging some of them.
•
•
Appliances plugged into the same circuit as the telephone can cause
interference. Try moving the appliance or telephone to another outlet.
If you hear
noise or
interference
during a call
Disconnect the telephone from the modular jack and connect another
telephone. If calls are still not clear, the problem is probably in your
wiring or local service. Call your local telephone service company.
27
ATT-1855CIB-d05.qxp 4/8/2005 5:39 PM Page 28
Appendix
In case of difficulty
•
•
•
If a caller leaves a very long message, part of it may be lost when the
system disconnects the call after 3 minutes.
Incomplete
messages
If the caller pauses for more than 7 seconds, the system stops
recording and disconnects the call.
If the system’s memory becomes full during a message, the system
stops recording and disconnects the call.
•
Increase speaker volume.
Difficulty hear-
ing messages
•
•
Make sure that the answering system is on.
System does not
answer after
correct number
of rings
If Toll Saver is activated, the number of rings changes when you have
new messages waiting (see page 21).
•
•
In some cases, the system may be affected by the ringing system
used by the local telephone company.
If the memory is full or the system is off, the system will answer after
10 rings.
•
You need to reset the answering system clock (see page 18).
“CL” flashes in
message window
•
•
Make sure to enter your Remote Access Code correctly (see page 25).
System does
not respond
to remote
Make sure you are calling from a touch-tone phone. When you dial a
number, you should hear tones. If you hear clicks, the phone is not a
touch-tone telephone and cannot activate the answering system.
commands
•
•
The answering system may not detect the Remote Access Code
while your announcement is playing. Try waiting until the announce-
ment is over before entering the code.
There may be noise or interference on the phone line you are using.
Press dial-pad buttons firmly.
•
•
•
When you record your announcement, make sure you speak in a
normal tone of voice, about 9 inches from the telephone.
Announcement
message is not
clear
Make sure there is no “background” noise (TV, music, etc.) while
you are recording.
Record your outgoing announcement from a remote telephone
(see page 25).
28
ATT-1855CIB-d05.qxp 4/8/2005 5:39 PM Page 29
Appendix
Index
A
M
AC adapter, 5, 7
Making calls, 8
Memos, 23
Access code, 25
Alert tones, 26
Menus, 2, 10-11, 21
Message alert, 21
Messages, 17-25
Microphone, 19, 23
Missed calls, 14
Mute, 9
Answering calls, 8
Answering system, 17
announce only, 20
delete messages, 22
feature options, 21
outgoing announcement, 19
memos, 23
N
play messages, 22, 25
remote access, 25
Number of rings before answer, 21
O
C
On/off button, 17
Call logs, 14
Caller ID, 14
delete entries, 15
dial entries, 16
Call screening, 21
Call waiting, 4, 9
Outgoing announcement, 19
P
Priority Call, 21
Playback (messages), 22
Problems, 27
D
Q
Day/time, 18
Delete Call Log entries, 15
Dialing,
Quick reference guide, 2
R
manual dialing, 8
memory dialing, 12
Receiving calls, 8
Redial, 8
Repeat, 22
Ring tone options, 21
Ringer volume, 8
E
Ending calls, 8
Error tones, 26
S
F
Skip, 22
Sounds & alerts, 26
Speakerphone, 8
Flash (switchhook flash), 9
I
T
Incoming call log, 14
Incoming calls, answering, 8
Incoming messages, 17
Indicator lights, 26
Time, 14, 18
Tones, 26
Troubleshooting, 27
V
L
Volume controls, 8, 9
Last number redial, 8
29
ATT-1855CIB-d05.qxp 4/8/2005 5:39 PM Page 30
Copyright © 2005 Advanced American Telephones.All Rights Reserved.
AT&T and the Globe Design are trademarks of AT&T Corp.,
licensed to Advanced American Telephones. Printed in China. Issue 3 AT&T 07/23/05.
|
Hanns G HH191DP User Manual
Hanns G Computer Monitor HA222 User Manual
Electrolux 584163 User Manual
Dell POWEREDGE 300 User Manual
Daewoo DTQ 27U8SCN User Manual
Cecilware BC 1836 User Manual
Asus P5P800 SE User Manual
Asus P5A User Manual
Asus Computer Hardware F2A55 M LK User Manual
AMCC 9550SX 2 User Manual